Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: NASCAR sway bar install on the rear of the Mirage

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Champion Member Blueovalz's Avatar
    Join Date
    Jul 2014
    Location
    Little Rock, AR
    Posts
    279

    NASCAR sway bar install on the rear of the Mirage

    I finally decided on a sway bar configuration for the project. I found a couple of sway bars that would fit (Porsche 911 rear bar was one that would fit almost perfectly), but not knowing exactly what I needed in terms of size, I'm not ready to use them. Because of limited sizes from donor-car bars, and not wanting to commit to custom bent bars (unless I knew exactly what I needed), I decided on a NASCAR style bar. They are cheap on Ebay, come in a multitude of sizes, and can provide an almost infinite range of stiffness with the long arms. I chose a medium-sized diameter of splines (1.25") (because of the long list of available diameters), and am using the standard 37.5" length. I was able to purchase a group of the smallest 4 bars on Ebay for real cheap (new), so the only thing left to do was install them. Again, my chassis does not lend well to the addition of yet another piece of equipment in an already very cramped space under the bodywork.

    These bars can use a tubular housing, which I chose to insert in place of the existing rear bulkhead crossbar over the transaxle. Thus the bar's housing in essence is a part of the framing. I removed the existing brace, modified the posts that hold the cross-bar, and then machined and welded all the aluminum parts needed to bolt the sway bar housing back in place.

    Existing cross-bar:


    After the top of both posts was cut off, I inserted a machined piece of aluminum into the ends (drill press and carbide tipped hole saws make a poor man's milling machine):


    Drill and tap threads to fix plates into each post:


    Then weld saddles (2" square tubing) onto the top of each plate that will hold the bar's housing in place. I welded a long piece in place, and then cut the ends off after it was all done to ensure they were aligned with each other:


    The housing in place, but not yet welded to the saddles. Plastic bushings slide into each end, and then the sway bar slides into the bushings, with shaft collars on each side to hold the bar and bushings in place:


    With bar installed:

  2. #2
    Pole Position Member
    Join Date
    Aug 2014
    Location
    Cape Coral, Florida
    Posts
    68
    Awesome job! I like the innovation in your mounting solution...wish I had the fabricating skills to do stuff like that.

    Dan

  3. #3
    Administrator Sulley's Avatar
    Join Date
    Sep 2012
    Location
    Atlanta
    Posts
    294
    I would love to see that car when it is finished!

  4. #4
    Champion Member Blueovalz's Avatar
    Join Date
    Jul 2014
    Location
    Little Rock, AR
    Posts
    279
    Quote Originally Posted by Sulley View Post
    I would love to see that car when it is finished!
    Funny thing is that I would too. Perhaps next summer I can get some warm weather painting done, and have this thing "finished" enough to where I can make improvements or enhancements as time and money permits.

  5. #5
    Administrator Sulley's Avatar
    Join Date
    Sep 2012
    Location
    Atlanta
    Posts
    294
    You have to have it ready in time for the Manta reunion!

  6. #6
    Champion Member Blueovalz's Avatar
    Join Date
    Jul 2014
    Location
    Little Rock, AR
    Posts
    279
    And then find a way to get it there.

  7. #7
    Administrator Sulley's Avatar
    Join Date
    Sep 2012
    Location
    Atlanta
    Posts
    294
    With your skills you can fabricate a trailer!

  8. #8
    Champion Member Blueovalz's Avatar
    Join Date
    Jul 2014
    Location
    Little Rock, AR
    Posts
    279
    I would have had one a long time ago, but storing it is the problem. Kinda like a boat...its more economical to rent one a few times out of the year than own one.

  9. #9
    Champion Member Blueovalz's Avatar
    Join Date
    Jul 2014
    Location
    Little Rock, AR
    Posts
    279
    Finished up the rear X-bracing that I had to modify (re-make) after the fabrication of the sway-bar housing.



    In the meantime, another issue is popped up in that the sway bars I have are not timed properly. In other words the splines are not aligned end to end, so I've got about a 3/4" to 1" difference in link length between the two sides. Odd stuff for what was advertised as "new" bars. Anyway, they are serving their purpose (mock up and testing), and I will be going to hollow bars as soon as I determine what size I want to settle on.
    Last edited by Blueovalz; 12-16-2014 at 04:19 PM.

  10. #10
    Administrator Sulley's Avatar
    Join Date
    Sep 2012
    Location
    Atlanta
    Posts
    294
    So will you be using hollow bars with HJ?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •