Results 1 to 9 of 9

Thread: Almost finished after 5 years

  1. #1
    Pole Position Member
    Join Date
    Aug 2014
    Location
    Cape Coral, Florida
    Posts
    68

    Almost finished after 5 years

    Found this about 5 years ago under a tarp in a guy's driveway and figured I could have it on the road in no time....

    Got all the body parts back from the painter just before Christmas and now need to get the windshield installed, get some plates and go for a shakedown run....

    Folks think I am joking when I say, "I look up at people in Corvettes".Click image for larger version. 

Name:	01 arrival.jpg 
Views:	16 
Size:	86.9 KB 
ID:	985Click image for larger version. 

Name:	qtr frt small.jpg 
Views:	25 
Size:	94.0 KB 
ID:	986Click image for larger version. 

Name:	qtr rear glass in small.jpg 
Views:	24 
Size:	94.6 KB 
ID:	991Click image for larger version. 

Name:	open side small.jpg 
Views:	26 
Size:	97.5 KB 
ID:	992Click image for larger version. 

Name:	side by side low small.jpg 
Views:	26 
Size:	100.5 KB 
ID:	987Click image for larger version. 

Name:	high rear compare small.jpg 
Views:	23 
Size:	92.3 KB 
ID:	988Click image for larger version. 

Name:	interior small.jpg 
Views:	22 
Size:	83.9 KB 
ID:	989Click image for larger version. 

Name:	engine small driver.jpg 
Views:	23 
Size:	96.2 KB 
ID:	990Click image for larger version. 

Name:	01 arrival.jpg 
Views:	16 
Size:	86.9 KB 
ID:	985Click image for larger version. 

Name:	qtr frt small.jpg 
Views:	25 
Size:	94.0 KB 
ID:	986Click image for larger version. 

Name:	qtr rear glass in small.jpg 
Views:	24 
Size:	94.6 KB 
ID:	991Click image for larger version. 

Name:	open side small.jpg 
Views:	26 
Size:	97.5 KB 
ID:	992Click image for larger version. 

Name:	side by side low small.jpg 
Views:	26 
Size:	100.5 KB 
ID:	987Click image for larger version. 

Name:	high rear compare small.jpg 
Views:	23 
Size:	92.3 KB 
ID:	988Click image for larger version. 

Name:	interior small.jpg 
Views:	22 
Size:	83.9 KB 
ID:	989Click image for larger version. 

Name:	engine small driver.jpg 
Views:	23 
Size:	96.2 KB 
ID:	990

  2. #2
    Pole Position Member
    Join Date
    Aug 2018
    Location
    Chatham ontario canada
    Posts
    54
    Looking great!

  3. #3
    Champion Member Blueovalz's Avatar
    Join Date
    Jul 2014
    Location
    Little Rock, AR
    Posts
    279
    Nice recovery on this one!

  4. #4
    Pole Position Member
    Join Date
    Jan 2019
    Location
    Western Canada
    Posts
    60
    looks awesome. I can't believe how low these cars are! I'll bet that Manta will run circles around that vette!

  5. #5
    Pole Position Member
    Join Date
    Aug 2014
    Location
    Cape Coral, Florida
    Posts
    68

    Thanks

    Quote Originally Posted by Blueovalz View Post
    Nice recovery on this one!
    It finally seems worth all the time and effort. Hope this inspires others to keep at it!

    Dan

  6. #6
    Pole Position Member
    Join Date
    Aug 2014
    Location
    Cape Coral, Florida
    Posts
    68
    Just hoping it runs well on the shakedown.... I need to learn its habits (good and bad) before I decide to hammer it...
    Dan

  7. #7
    Pole Position Member
    Join Date
    Jan 2019
    Location
    Western Canada
    Posts
    60
    Dan, what is your ground clearance from the bottom of the frame?

  8. #8
    Pole Position Member
    Join Date
    Aug 2014
    Location
    Cape Coral, Florida
    Posts
    68

    Ground Clearance

    Quote Originally Posted by marfen View Post
    Dan, what is your ground clearance from the bottom of the frame?
    Manta Mirage
    Ground to frame side rail behind front tire is 4.75".
    Ground to frame side rail ahead of rear tire is 5.5".
    Bottom of the leading edge of the nose of the car is 5" off the ground.
    Lowest point is probably the air dam I have back between the front tires at about 3" (but it is far enough back it should miss most stuff unless I try to straddle roadkill).

    2008 Corvette (I measured ours)
    Ground to frame side rail behind front tire (at jack point) 5".
    Ground to frame side rail ahead of rear tire (at jack point) 5.5"
    The Corvette side sills wrap under the car and sit .25-.5" below the frame jack points.
    Corvette front spoiler leading edge is 3" off the ground and it is just behind the nose of the car.

    Both cars will scrape the nose/spoiler on some driveways if I don't approach at an angle.

    Hope this helps.
    Dan

  9. #9
    Pole Position Member
    Join Date
    Jan 2019
    Location
    Western Canada
    Posts
    60
    Thx Dan. I appreciate you taking the time to measure up things. I figured your Manta was a bit lower but what you have for clearance is great so you can drive it on the street. Thx for the measurements of the vette too. Awesome.
    Any chance you can measure on the vette how high the bottom back of the rear suspension cradle is off the ground? I'm going to be running C5/6 rear suspension setup on mine and that measurement will be a good starting point for mocking up rear suspension.
    You're going to have a great summer with those two cars to A/B performance wise.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •